République Tchèque, BrnoMars 2010
Customer information
Dear customers,
We focussed all our activities in Wiehl!
Following, please find your contacts to the sales, after sales and spare parts department.
In case there have been any inconveniences or delays caused by our relocation we apologize sincerely.
| Sales Furnaces: | |
| E-Mail: | sales@strikowestofen.com |
| Phone: | 0049 22 61 / 70 91 - 112 |
| Fax: | 0049 22 61 / 70 91 - 107 |
| Sales Spare Parts: | |
| E-Mail: | spares-repairs@strikowestofen.com |
| Phone: | 0049 22 61 / 70 91 - 321 |
| Fax: | 0049 22 61 / 7 64 78 |
| After Sales Service: | |
| E-Mail: | service@strikowestofen.com |
| Phone: | 0049 22 61 / 70 91 - 129 |
| Fax: | 0049 22 61 / 7 64 78 |
Septembre 2009
PSA investit massivement dans la fusion d’Aluminium
En mars 2009, la société PSA PEUGEOT CITROEN a mis en service le troisième four de
fusion et de maintien de StrikoWestofen GmbH à l’usine de Charleville-Mézières. Le
StrikoMelter® four de fusion de type WHS-T a une capacité de fusion de 5.000 kg d‘Aluminium par heure et un bain de maintien d’une capacité de 10 to. StrikoWestofen a garanti une consommation d’énergie en-dessous de 600 kWh pour fondre et réchauffer 1 to d’Aluminium à la température prescrite de 720 °C. Cette nouvelle installation remplace deux fours d’un autre fournisseur.
 |
Téléchargement: Article comme PDFSWO_Pressemitteilung_PSA_F_20090923.pdf (309 kb) |
|
|
||
| StrikoMelter® de type WHS-T, à faible consommation d’energie et degré d’automatisation élevé | ||
Avril 2008
In-House Recycling of Aluminum-Chips in Foundries
Al Chip Melting with the StrikoMelter®
For the first time in history a metal yield of 98% has been achieved in a foundry with a StrikoMelter® during in-house recycling of Al chips.
The pre-dried Al chips are fed into the side pocket of the StrikoMelter® and are drawn homogenously under the surface of the metal bath. There, they are melted under airtight conditions. For a maximum metal yield StrikoWestofen uses the Metaullics system.
A high profitability is guaranteed which can be increased further by an optimization of the chip pre-treatment.
As an alternative to the ChipMelter which is exclusively used with chip melting StrikoWestofen also offers, depending on the customer’s demand, the CombiMelter which incorporates comprises the ETAmax® shaft furmace for melting ingots and returns. This results in a very low energy demand due to the combined use of waste heat.
The pre-dried Al chips are fed into the side pocket of the StrikoMelter® and are drawn homogenously under the surface of the metal bath. There, they are melted under airtight conditions. For a maximum metal yield StrikoWestofen uses the Metaullics system.
A high profitability is guaranteed which can be increased further by an optimization of the chip pre-treatment.
As an alternative to the ChipMelter which is exclusively used with chip melting StrikoWestofen also offers, depending on the customer’s demand, the CombiMelter which incorporates comprises the ETAmax® shaft furmace for melting ingots and returns. This results in a very low energy demand due to the combined use of waste heat.